stainless steel pallet trucks are many reasons: the valve stem spring failure; inclined cylinder wall and seal excessive wear and tear; inclined cylinder too much dirt or seal too tight; piston card Cylinder wall or piston rod bending. The solution is the spring failure should immediately replace the new spring; seal serious wear and tear should be replaced immediately, if the cylinder is also serious wear and tear also need to replace the cylinder; tank dirt to clean more cleaning, as too tight seal can be adjusted, Deterioration of the wearing parts of the piston should be replaced immediately.

Counter-balance Stacker gear pump and pump wear excessive, the valve did not overflow valve high pressure improper lifting can cause or unable to lift, need to replace the gear pump, and high pressure can be re-adjusted. In addition there are oil pipeline oil leakage, hydraulic oil temperature is too high, there are jamming mast and the motor speed is too low or lead to lifting the inability to lift the reason, the solution is to check the hydraulic pipe repair Replace the unqualified hydraulic oil and check the cause of the oil temperature increase, adjust the mast slide and check out the motor failure and remove.

3300 lb Semi Electric Straddle Stacker 118 Inch Lift

An affordable drum semi electric stacker with power lift and manual push-pull functions, Stärke's EMSA3300 features fully adjustable forks and straddle legs with three different width selections to accommodate various pallet sizes. The unit also includes an efficient 12V battery pack and an on-board charger , Which allows for long intervals between charges.

Electric forklifts typically use a separate motor to drive the gear pump, providing hydraulic power for the lifting and tilting of the mast work system. At present domestic galvanizing hand pallet Jack, because there is no hydraulic motor speed control, hydraulic motor in the start, only high-speed rotation, will not change with the function and pressure automatically adjust the excess flow only through the relief valve flow back to the tank, Resulting in energy waste. Foreign new forklift, such as the LINDE E20 drum semi electric stackers, the use of advanced hydraulic pulse control technology, hydraulic pump pulse controller can respond to the hydraulic circuit, automatically balance the motor speed and fuel consumption, saving energy, the advantages of this control Is the high power utilization, no voltage peak, low noise hydraulic system, hydraulic components, wear and tear is also low, thus greatly improving the vehicle's reliability and service life.

Our straddle semi electric stackers are one of our most versatile pieces of machinery

Cnmhe’s new series of walkie reach stacker is comprised of seven models, including straddle, counterbalanced and reach stackers with capacities ranging from 2,000 to 4,000 pounds. These versatile and easy to use lift trucks are ideally suited for a variety of pedestrian truck applications, from manufacturing environments and retail store operations to general transportation and product distribution.
Our straddle semi electric stackers

are one of our most versatile pieces of machinery. The straddle semi electric stacker can lift goods from 400kg up to 1500kg and up to 3.5m high. A key feature of the manual hydraulic pallet stacker is their adjustable forks and load arms, ensuring effective operation. One of the many advantages of a semi electric pallet stacker is its ability to save time and complete tasks in a safe and manageable way. All of our manual hydraulic pallet stackers feature integrated chargers and low maintenance batteries. The wheel rollers are made from polyurethane, so that your machine runs smoothly and quietly. They also benefit from overload protection, providing you with absolute peace of mind.

we serve our valued clients with a wide range of Hand Stacker

Owing to the years of industrial experience, we have been able to serve our valued clients with a wide range of Hand Stacker that is highly acclaimed in various warehouses for handling of materials. The offered stacker is manufactured by our skilled professionals using quality tested components and progressive technology in adherence to set industry standards. Further, our quality experts rigorously examine this electric stackers

 on different quality parameters in order to make sure its flawless operations.

cnmhe electric stackers are designed to withstand the daily rigors of highly intensive load lifting

fork over stacker

is highly suitable for general load handling functions that involve tight sections and elevated heights.cnmhe electric stackers are designed to withstand the daily rigors of highly intensive load lifting as well as more demanding transport and stacking procedures.
If you take a closer look at the cnmhe fork over stacker for sale, you’ll notice that the forks are positioned directly above the outriggers.  This increases cube utilization considerably and helps achieve optimum productivity in both commercial and industrial work settings, making them ideal for that involves skids and European pallets.

Walkie type electric stacker provides a cost effective solution for applications

Walkie type electric stacker provides a cost effective solution for applications involving medium lifting storage and short distance pallets transportation.
Walkie reach stacker advantages:
• Compact structure makes it’s easy to be used in narrow aisle.
• Stepless speed control, smooth/controllable speed.
• Fork can be tilted forward 3 degree or backward 5 degree.
• Intelligentized regenerative brake system.
• Advanced AC control system Intelligentized regenerative brake system.
• Emergency reversing device.
• Auto deceleration system utilizes regenerative braking.
• With lifting limit switch to shut off pump motor at the max. lifting height.
• Standing driving motor system has a small turning radius. The motor structure is water-proof and dust-proof.

CNMHE Electric stacker with lift to height from 1.6m to 3.5m

CNMHE Electric stacker with lift to height from 1.6m to 3.5m. to easily negotiate over ramps and bridging plates, can carry two pallets at same time, widely used in low shelves warehouse and small supermarket.
CNMHE Electric pallet stacker Advantages:
• Advanced AC control system eliminates the motor brushes and directional contactors, which makes the minimal maintenance requirements. Intelligentized regenerative brake system.
• Platform with speed sensor.
• With platform is with speed sensor.
• With guard on both sides, protect operator when drive at high speed of the trucks.
•Emergency reversing device.
• Built-in pressure relief valve protects the trucks from overloads.
• With Speed sensor under platform can switch drive speed to Low/high speed when platform is closed/opened.

Our walkie reach stacker feature

walkie reach stacker combines the tight turning advantages of a straddle stacker with the versatility of a counterbalanced stacker. Our walk behind reach stackers are a great option for sideloading trailers, doing general material handling, or navigating tight areas with the ability to right angle stack.

Our walkie reach stacker feature: 

• Heavy duty pantagraph reach mechanism with 24” of extension 

• Control arm coupled driveline provides intuitive and direct operator control.

• Premium steel frame construction protects components and reduces maintenance. 

• Premium steel mast construction provides extended service life and load stability. 

• Ergonomic handle with reversing switch, horn and wrap around hand guard. 

• A wide variety of vehicle options to meet your specific application needs.

CNMHE electric Stackers's compact design

CNMHE electric Stackers's compact design is ideal for operation in narrow aisles with step-less speed control for smooth, consistent speed; a vertical, high efficiency & low noise drive wheel; and an intelligent regenerative braking system.
Walkie reach stacker combines the tight maneuvering ability of a walkie straddle stacker with the operating flexibility of a counterbalanced truck. A pantograph extends the handled loads beyond the straddle legs and can be retracted for compact turns and tight manuevering. Power steering, side shift, proportional hydraulics, and tilt all result in intuitive control and exceptionally versatile performance.

The walkie reach stacker has advantageous head-length and multi-function

The walkie reach stacker has advantageous head-length and multi-function, bottom mounted steering control handle gives you incredible load handling control with excellent maneuverability.
Walkie Reach Stacker uses a pantograph to combine the tight maneuvering ability of a walkie straddle stacker with the operating flexibility of a counterbalanced truck. Power steering, proportional hydraulics, and tilt result in intuitive control and versatile performance.
The light duty electric stacker series features a tough, unitized construction that is robotically welded, for superior reliability. Serial communications and solid state switches with soldered wire connections increasing reliability and uptime, replace the hydraulic pump contactor, forward and reverse contactors and their corresponding maintenance costs.

These walkie reach stacker are designed for indoor

These walkie reach stacker are designed for indoor use and ideally suited for a wide variety of applications such as dock operations, general warehouse and storage, home improvement warehouses, and paint and chemical distribution.
Whether your material handling jobs include unloading or loading trailers, dockside maneuvering, or stocking, the CNMHE electric Stackers line of motorized pallet trucks gives you big capacity and productivity with the operational cost of a walkie rather than a rider. And our superior ergonomics along with the versatility of user selectable performance modes will help to increase your productivity.
Bottom mounted steering control handle’s ergonomic, easy-to operate, finger tip control of proportional lift/ lower, reach extension/retraction, travel speed and direction, and an optional sideshift makes load handling easier and more precise, increasing your productivity.

walkie reach stacker is designed to provide excellent visibility

Walkie reach stacker is designed to provide excellent visibility and is equipped with a horn as standard equipment. However, environments with high levels of ambient noise may find it difficult to hear the horn when sounded. The warning light option may assist in making other workers aware of the CNMHE electric stackers in use.
For applications with unique handling needs, the Auxiliary Hydraulic Function Valve and Hose Package provides additional function for custom handling in addition to lift/lower, tilt and sideshift. The sideshift function provides sideways movement of the carriage permitting a load to be picked up or put away even if it is not perfectly aligned with the Stackers.

CNMHE Walkie Reach Stacker

CNMHE Walkie Reach Stacker
If you are looking for a reach stacker to use in your load lifting operation then the CNMHE walkie reach stacker should certainly be among your options. CNMHE carries a wide range of reach stackers that are all designed to meet the varied demands of different industries and operations. CNMHE allows its customers to choose the right powered stacker based on several factors such as load requirements, floor conditions and more.
Below are some of the reach stacker models:
Large, durable and built for heavy-duty and long-term use.
Low maintenance costs.
Compact built which enables it to navigate cramped or tight spaces.

Electric forklift before the use of occasions and features

Forward forklift electric forklift truck frame may be moved back and forth, in which masthead forward forklift is the operation of mast moving fork forward, out to the front fork to take or put down the goods, walking Fork with goods recovery, so that the focus of the goods in the support surface; and fork forklift truck is moving forward to the front of the fork to carry out the operation of the fork, the fork moving fork fork moving back to the support plane Inside.
Forward electric lifters has two forward legs, legs are higher, the front legs have two wheels, the role of outrigger is to ensure that the stability of the forklift when the load. Compared with the leg-type forklift, the front wheel is larger, the legs are higher, the operation can not pierce the bottom of the goods, and mast can take full lifting arrangements along the inner leg of the rail movement, Fork to take a little lifting after a high degree of goods can be retracted to ensure the stability of forklift operation. Forward forklift and the same pin-type forklift trucks are the focus of the goods fell into the support plane of the vehicle, so excellent stability. Suitable for workshop, warehouse operations. Fork-lift truck from the smaller weight, the choice of electric motor drive.
The gantry of the forward-moving electric forklift can be moved forward along the rail on the inside of the leg with a lifting arrangement to facilitate fork-lift. Fork to complete the goods, lifting a short height later, the mast and the inner leg along the track back to the original position.
Front-lift electric forklift with a balance of forklift and electric stacker with the characteristics. When the mast to rise to the top, the load center of gravity falls on the outside of the fulcrum, at the moment is equivalent to electric stacker. The two functions of the contact, making the forklift has the flexibility and high load operation of the interests of the same volume and weight will not increase many, the car will not increase the weight of many, car weight of about 500kg, together can save space and reduce the turning radius , Suitable for narrow channel indoor storage operations

Manual hydraulic loader does not rise up how it happened?

galvanizing hand pallet truck is the most commonly used handling tool in factories, warehouses, workshops, because the shape is simple and powerful, but this simple device will often appear this or that problems, such as slow rise, slow down, or simply do not rise .
L does not rise, many people think it is not bad? In fact, this is not the case, many times only manual hydraulic pump truck inside the air, leading to the time of the hydraulic does not rise or slow. At this time only need a simple row of air can make manual handling vehicles intact.
The method of exhaust air is very simple, the following for you:
Manual hydraulic pallet truck generally has three stalls
1, the middle position is blocked, the stall car neither rise nor fall.
2, dial up is the gap, which is down the stalls, pressure relief gear.
3, down is linked to file, close the oil seal is allowed to increase its hydraulic pressure.
We only need to manually shift the stall gear stalls up, and then as usual pressure from the same pressure a few handles, this time although the car will not rise, but can exclude the air inside the pump, about 10-20 under pressure You can.

Superior performance and advanced technology

Superior performance and advanced technology, that is what is behind CNMHE Warehouse Equipment. Command demanding production schedules and maximize operator productivity with CNMHE Walkie reach stacker and Electric Pallet Jacks.
CNMHE's Electric Pallet Jack is running longer and spending less. While other manufacturers may offer AC technology, Jungheinrich developed and pioneered AC technology.
There are a multitude of different factors when purchasing equipment for a specific application. Our professional sales team can make the process a lot easier and ensure you get the most from your investment.

Walkie Electric Fork Over Stackers are highly suitable for general load handling functions

Walkie Electric Fork Over Stackers are highly suitable for general load handling functions that involve tight sections and elevated heights. CNMHE electric stackers are designed to withstand the daily rigors of highly intensive load lifting as well as more demanding transport and stacking procedures.
If you take a closer look at the fork over stacker for sale, you’ll notice that the forks are positioned directly above the outriggers.  This increases cube utilization considerably and helps achieve optimum productivity in both commercial and industrial work settings, making them ideal for that involves skids and European pallets.

Fork over stacker is a comfortable

Fork over stacker is a comfortable and high secure fork-over leg electric stacker with high lifting height and free lifting, equipped with CNMHE-Made EPS and AC drive system.
Standard equipped with 280Ah lead-acid sideway battery. 3 different lowering speed, slow-medium-fast suitable for different situations. Chassis design life up to 10 years. Injection mold cover, Stellana Brand Wheels offer best quality. CNMHE-made EPS and Curtis controllers can real-time protect the vehicle control from circuit overvoltage, under voltage, over current, excess temperature, Short circuit.
Double controllers can safely reduce the traveling speed under the condition of Mast electric lifts and sharp turn in the corner. The lifting Limit function can protect hydraulic motor, save energy and battery. Self-made handle can be modified for cold store application.

Walkie Electric Fork Over Stackers

Walkie Electric Fork Over Stackers
High lift electric walkie fork over stackers are designed to ideally lift and transport loads within wire baskets and steel containers as well as on pallets and palletized skids. With their rugged design and compact chassis, these fork over trucks provide more versatility than comparable straddle stackers for moving loads in restricted areas. This is because the outriggers are positioned beneath the forks, eliminating the additional width required by the outriggers on traditional straddle stackers. Allow us to customize your electric fork over stacker to meet your needs.

A CNMHE electric Stackers with reliable performance

A CNMHE electric Stackers with reliable performance that operates quietly. high lifting stacker short wheel base provides outstanding maneuverability, while ergonomic controls reduce worker fatigue. A narrow mast and offset control handle allows the operator to have exceptional front visibility. A special reverse "belly bump" switch helps protect operators when backing up, and full brakes stop motion when handle is released. Thumb controls make steering intuitive.
Rechargeable battery
Drive wheel fully shrouded to protect operator's feet;
Comfort grip controls with switch redundancy for left and right hand operation;
Includes battery status indicator and charger controls in convenient location;
Auto reverse "belly bump" switch protects operators when working in close spaces.

Fork Over Stacker is a comfortable and high secure fork-over leg electric stacker

Fork Over Stacker is a comfortable and high secure fork-over leg electric stacker with high lifting stacker height and free lifting, equipped with CNMHE Made EPS and AC drive system.
Standard equipped with 280Ah lead-acid sideway battery. 3 different lowering speed, slow-medium-fast suitable for different situations. Chassis design life up to 10 years. Injection mold cover, Wheels offer best quality. EPS and Curtis controllers can real-time protect the vehicle control from circuit overvoltage, under voltage, over current, excess temperature, Short circuit.
Double controllers can safely reduce the traveling speed under the condition of Mast lifting and sharp turn in the corner. The lifting Limit function can protect hydraulic motor, save energy and battery. Self-made handle can be modified for cold store application.

Walkie reach stacker are designed to ideally lift and transport loads

CNMHE electric walkie reach stacker are designed to ideally lift and transport loads within wire baskets and steel containers as well as on plastic pallets and palletized skids. With their rugged design and compact chassis, these fork over stackers provide more versatility than comparable straddle stackers for moving loads in restricted areas. This is because the outriggers are positioned beneath the forks, eliminating the additional width required by the outriggers on traditional straddle stackers. Allow us to customize your electric fork over stacker to meet your needs.
Fork-over stacker is designed for narrow aisles and confined areas, with fixed legs for open pallets and skids only. Includes On Off switch and illuminated volt meter to indicate battery and charge status. Optional forks and platforms available separately.

walkie reach stackers offer a number of advantages over ride-on forklifts

For the handling of lighter loads, many operations increasingly favour the use of pedestrian trucks or walkie reach stackers which offer a number of advantages over ride-on forklifts. In response the Combi-WR Walkie Reach stacker was released, the first purpose built 4-way pedestrian reach stacker which combines multi-directional travel with innovative features.
Walkie Reach Stacker combines the tight maneuvering ability of a walkie straddle stacker with the operating flexibility of a counterbalanced truck.  A pantograph extends the handled loads beyond the straddle legs and can be retracted for compact turns. Power steering, side shift, proportional hydraulics, and tilt all result in intuitive control and exceptionally versatile performance.

CNMHE electric stackers are designed to suit warehouse applications

CNMHE electric stackers are designed to suit light to medium-duty load handling and warehouse applications. Our comprehensive range of stackers include standard, walkie reach stacker, straddle, counterbalance and semi-electric versions.
Powerful, fast and easy to use, Enforcer pedestrian and platform stackers are ideal for stacking, pallet handling, and order picking operations. They are equally effective for routine horizontal transport and all other short-run palletised load management in narrow aisles and tight sections. Enforcer electric stackers are widely used to augment low-intensity load handling applications across various commercial and industrial environments.

electric stackers are suited for a wide variety of applications

The electric stackers are designed for indoor use and ideally suited for a wide variety of applications such as dock operations, general warehouse and storage, home improvement warehouses, and paint and chemical distribution.
Whether your material handling jobs include unloading or loading trailers, dockside maneuvering, or stocking, the walkie reach stacker line of motorized pallet trucks gives you big capacity and productivity with the operational cost of a walkie rather than a rider. And our superior ergonomics along with the versatility of user selectable performance modes will help to increase your productivity.
The heavy-duty walkie stacker series features a tough, unitized construction that is robotically welded, for superior reliability.

Heavy duty electric fork over stacker

Heavy duty and high secure duplex mast electric fork over stacker with 1000kg capacity, maximum lifting height 3.6m. This is a model without electric power steering system but longer handle, which is still very easy to operate.
• One piece fork: with 10mm thickness. CNMHE electric lifts proudly declare that there are no possibility of deformation under high frequency using.
• Two pieces handle tube: two piece dismountable handle tube, made from high quality mold, which make assembly and dismantle of handle tube to be    much easier.
• Stong H profile mast, stronger mast make lifting to be safe and fluent.
• High performance AC driving Motor and DC hydraulic motor, with no electric power steering system, but thanks to the longer handle which offer nice operation experience.

Fork Over Stackers are designed to move skids

Fork Over Stackers are designed to move skids, wire baskets/cages and Euro-type pallets. Eliminate outrigger space and improve cube utilization with this stacker.
Electric walkie high lift stackers are designed to ideally lift and transport loads within wire baskets and steel containers as well as on plastic pallets and palletized skids. With their rugged design and compact chassis, these fork over trucks provide more versatility than comparable straddle stackers for moving loads in restricted areas. This is because the outriggers are positioned beneath the forks, eliminating the additional width required by the outriggers on traditional straddle stackers. Allow us to customize your electric fork over stacker to meet your needs.

Walkie reach stacker is a comfortable fork-over leg electric stacker

Walkie reach stacker is a comfortable and high secure fork-over leg electric stacker with high lifting height and free lifting, equipped with Liftstar-Made EPS and AC drive system.
Standard equipped with 280Ah lead-acid sideway battery. 3 different lowering speed, slow-medium-fast suitable for different situations. Chassis design life up to 10 years. Injection mold cover, Stellana Brand Wheels offer best quality. CNMHE-made EPS and Curtis controllers can real-time protect the vehicle control from circuit overvoltage, under voltage, over current, excess temperature, Short circuit. Double controllers can safely reduce the traveling speed under the condition of Mast lifting and sharp turn in the corner. The lifting Limit function can protect hydraulic motor, save energy and battery. Self-made handle can be modified for cold store application.

Fully powered stacker with reliable performance

Fully powered stacker with reliable performance that operates quietly. Its short wheel base provides outstanding maneuverability, while ergonomic controls reduce worker fatigue. A narrow mast and offset control handle allows the operator to have exceptional front visibility. A special reverse "belly bump" switch helps protect operators when backing up, and full brakes stop motion when handle is released.
The design of the high lifting stacker puts focus on the safety and ergonomic working conditions of the user. The ergonomic correct handle ensures the user a relaxed hold. The Pallet Stacker is compact in its design; hence it is very maneuverable in tighter spaces compared to a fork lift. High quality of the Pallet Stacker is ensured through an extended test program in cooperation with experts in health and safety.

CNMHE AC&EPS fork over stackers guarantee optimal stabilty and proven reliability.

Equipped with CNMHE designed EPS system and high performance AC drive system, WS03-12, WS93-14/16/18/20, WS95-16/18 and WS35-16/18/20 fork over stackers are the updated version and the relevant tests were completed in 2007. With the improvements in 2008, CNMHE AC&EPS fork over stackers guarantee optimal stabilty and proven reliability.
High lift electric walkie fork over stackers are designed to ideally lift and transport loads within wire baskets and steel containers as well as on plastic pallets and palletized skids. With their rugged design and compact chassis, these fork over trucks provide more versatility than comparable straddle stackers for moving loads in restricted areas. This is because the outriggers are positioned beneath the forks, eliminating the additional width required by the outriggers on traditional straddle stackers.

light duty walkie reach stacker operator to pinwheel in tight spaces

light duty walkie reach stacker provides added control along with a crawl speed function that allows the operator to pinwheel in tight spaces.
High lift electric fork over stackers are designed to ideally lift and transport loads within wire baskets and steel containers as well as on plastic pallets and palletized skids. With their rugged design and compact chassis, these fork over trucks provide more versatility than comparable straddle stackers for moving loads in restricted areas. This is because the outriggers are positioned beneath the forks, eliminating the additional width required by the outriggers on traditional straddle stackers. Allow us to customize your electric fork over stacker to meet your needs.

Platform pallet truck combine manoeuvrability with low operating costs

Platform pallet truck combine manoeuvrability with low operating costs. Some models have a folding platform or straddle legs. These stackers are ideal for low-mid level racking and work well on ramps.
Rider electric pallet stackers are suitable for transporting goods over longer distances or for working in restricted spaces. Heavy duty motors provide stability and smooth traction.
Counterbalanced stackers provide a superior performance when stacking closed or open pallets in confined spaces. They are ideal for demanding operations.

The Cnmhe range of pallet stackers and lifters deliver energy efficiency

The Cnmhe range of pallet stackers and lifters deliver energy efficiency, high performance, driver comfort, and low maintenance costs for the most demanding warehouse applications.
These warehouse stackers are ergonomically designed to maximise operator productivity when placing goods into low to mid-level racking.
Platform pallet truck are suitable for intense use in limited spaces and when storing goods in mid-high level racking. They are robust and have powerful acceleration.

Our electric stackers feature

Our electric stackers feature an ergonomic, multi-function handle head for greater comfort and control. The redeveloped state-of-the-art handle head is superbly engineered to suit the ergonomic needs of the fork over stacker operator.
Providing added control, the crawl speed function allows the operator to pinwheel in tight spaces. The handle can also be used in the fully upright position for increased productivity when turning in tight spaces.
The lift truck battery, when combined with energy efficient 3-phase AC technology, provides long operating times.

An electric stacker is sometimes called a walkie stacker

An electric stacker power propelled device that has a mast and forks that high lifting stacker loads and place them on shelves or rack beams.  It is stabilized by its outrigger legs and these must be considered when planning the rack and shelf layout.  Electric units are clean and efficient and prove to be the choice when working indoors.  Fully powered electric stacker transports loads throughout warehouse facilities quickly with less effort. Ergonomic handle feature easy-to-operate throttle with infinite adjustment of forward and reverse speeds. The emergency reverse belly switch instantly reverses direction and moves the unit forward until the swtich is released. Walkie stackers are good stewards of space and will operate in a very narrow aisle thereby adding to their value.

Choosing the perfect stacker for your needs

Choosing the perfect stacker for your needs is incredibly important. When deciding on the electric stacker for your business needs you should consider the maximum load that will need to be lifted as load capacities can range from 3000 to 12500 kilograms. Lift time may also be particularly important for your warehouse to run as effectively as possible. In addition to this, you also have the choice of manual stackers. We recommend opting for a powered drive if you or your staff will be moving large weights at height on a frequent basis as movement is smoother, more stable and it requires much less manual accuracy.

We offer a comprehensive range of electric stackers

We offer a comprehensive range of electric stackers from powered mini-lifters to heavy duty counterbalanced stackers to suit all budgets and requirements.
Electric stackers are the perfect choice for those who need more lifting capacity than a manual stacker whilst maintaining a compact size and easy manoeuvrability not often associated with forklift trucks.
If you require a larger load capacity and an increased lift height, we suggest electric pallet trucks which can handle up to 12500 kilogram loads. If you find that these electric stackers aren't quite what you're looking for then perhaps our compact manual stackers will suit your requirements.

our powered trucks and stackers

Every step is taken to ensure our powered trucks and stackers create a safer and ergonomically sound production environment for operators. They are also an excellent solution for every day material handling problems in industrial warehouses, shops and plants. The electric stacker models offer a variety of maneuvering and handling capabilities. The units can be equipped with a variety of options to handle products and pallets. Semi electric stackers combine manual traction and electric elevation. This is the ideal solution for moving medium-light loads.

The CNMHE range of pallet stackers and lifters

The CNMHE range of pallet stackers and lifters deliver energy efficiency, high performance, driver comfort, and low maintenance costs for the most demanding warehouse applications.
These warehouse stackers are ergonomically designed to maximise operator productivity when placing goods into low to mid-level racking.
Pedestrian stackers are suitable for intense use in limited spaces and when storing goods in mid-high level racking. They are robust and have powerful acceleration.
Ride on pallet trucks are suitable for transporting goods over longer distances or for working in restricted spaces. Heavy duty motors provide stability and smooth traction.
Counterbalanced stackers provide a superior performance when stacking closed or open pallets in confined spaces. They are ideal for demanding operations.

electric Stackers provides exceptional maneuverability

These electric Stackers are powered by standard single phase power and are highly reliable. They are available in portable or stationary configurations with fixed or telescoping masts and lifting heights up to 3.5m. Custom designed platform pallet truck is also available. Lift and lowering control is via standard remote control with coil cord. It provides exceptional maneuverability in tight areas like narrow aisle or inner space of truck.
The Electric mast reach stackers is the answer to your reach needs. Comes with the same great high standards as the Walkie Reach with many added options. Offering optional electric power steering for easy handling, deep/double reach.

We feel immensely pleased to offer electrical stacker

We feel immensely pleased to offer electrical stacker. By utilizing contemporary technology and utmost grade components in the manufacture, we are able to add the much-needed touch of exclusivity to the entire range. Also, we test the entire range on a series of parameters to flush out any possible flaw before the final dispatch from our end. Clients can avail the entire range from us at an affordable price.
semi electric stacker with the inclusion of contemporary technology, modern machines and sophisticated equipment in all our processes, we are able to manufacture, export, wholesale, distribute and supply precision-engineered Electric Stackers. Our offered range finds application in a large number of industries. Besides being manufactured from the high-grade raw materials, our offered stacker is examined thoroughly by our adept professionals ensuring its efficient functioning. Clients can avail the offered product from us at market leading prices.

The electric stacker models

The electric stacker models offer a variety of maneuvering and handling capabilities. The units can be equipped with a variety of options to handle products and pallets. Semi-electric stackers combine manual traction and electric elevation. This is the ideal solution for moving medium-light loads. hand and manual stackers are ideal for everyday handling of light to medium weight loads. drum stackers are designed and built to meet our customers’ special needs. we offers stainless steel powered truck equipment for food grade, clean room and corrosion resistant applications.

electric stacker is sometimes called walkie stacker

An electric stacker is sometimes called a walkie reach stacker.  A power propelled device that has a mast and forks that lift loads and place them on shelves or rack beams.  It is stabilized by its outrigger legs and these must be considered when planning the rack and shelf layout.  Electric units are clean and efficient and prove to be the choice when working indoors.  Fully powered electric stacker transports loads throughout warehouse facilities quickly with less effort. Ergonomic handle feature easy-to-operate throttle with infinite adjustment of forward and reverse speeds. The emergency reverse belly switch instantly reverses direction and moves the unit forward until the swtich is released. Walkie stackers are good stewards of space and will operate in a very narrow aisle thereby adding to their value.

We are the leading Manufacturers & Suppliers of Semi Electric Stackers

We are the leading Manufacturers & Suppliers of Semi Electric Stackers. This product is largely employed for application like rack and block stacking, vehicle loading and unloading, order picking and general pallet transports. Semi Automatic Stacker is made up from tested quality material and advance technology.
walkie reach stacker Features:
1, Polyurethane wheels
2, Various lift height
3, Application oriented attachments available in stacker instead of forks
4, Customised models available

Counterbalanced Electric Stacker manufactured

The Counterbalanced Electric Stacker manufactured by trusted vendors and supplied by us, is considered to be amongst the finest that are available in the market. Manufactured in accordance with the set industry norms and guidelines, its quality never deteriorates. Further, its reasonable pricing, performance and service life, makes the product highly asked for in the market.
Counterbalanced Stacker Features:
Superior strength
Easy to handle
Commendable functional life
Front / back mast tilt mimics counterbalanced forklift operation
Perfectly suited to less frequent, general purpose handling and stacking tasks

Electric Stacker Supplier has a wide range of products

Electric Stacker Supplier has a wide range of products which include Electric Stacker such as Manual Electric Stacker, Counterbalanced Electric Stacker and Semi Electric Stacker.
Manufactured in accordance with the set industry norms and guidelines, by trusted vendors, quality of this Manual Electric Stacker never deteriorates. The utilization of high grade raw materials and modern machines, in compliance with the set industry norms and guidelines, gives the product a longer functional life and an impeccable performance.
Features:
Commendable functionality
Longer service life
User friendly

This Semi Electric Stacker is an industrial material

This Semi Electric Stacker is an industrial material handling vehicle powered by battery. It is a very useful and essential equipment for transporting pallets and containers. it is designed to operate in narrow passages and limited space. They are ideal to use for loading and unloading. It features easy operation with little noise and pollution, and low malfunction rate.
The self propelled stackers is an efficient loading and unloading unit. It has an ergonomic feature that includes a height sensor to keep the load at a perfect working height. This unique material handling device allows you to load and unload heavy pallets with convenience and safety. Its infra-red height sensor automatically adjusts the fork height as you load and unload, eliminating the need to bend and lift.